# Honeywell Barcode Reader Config Tool

## What?

A Linux tool for configuring Honeywell barcode scanners via USB.

## Why?

I had obtained a used Honeywell Hyperion 1300G scanner, however it was locked down and secured with a password, and the password was unknown.

There is a Windows-only configuration tool from Honeywell called "EZconfig" with which the barcode scanners can be configured via USB, even when locked down.

To not rely on a Windows VM for configuring the scanner, I sniffed the USB traffic using Wireshark and extracted the relevant messages, and wrapped them in this tool.

## Usage

First of all, compile the program using `make`.  It depends only on `libusb-1.0`.

The configuration strings need to be provided as command line arguments.  You can provide multiple:

```
./honeywell-config <string1> [... <stringN>]
```

The commands sent to the scanner are prefixed with `>`, the (tokenized) responses from the scanner with `<`.

In general, please refer to your scanner's manual for configuration strings.

Here are some examples.

### Factory Reset

```
$ ./honeywell-config DEFOVR. DEFALT.
> DEFOVR.
< DEFOVR.
> DEFALT.
< DEFALT.
```

### Factory Reset - In one command

```
$ ./honeywell-config "DEFOVR;DEFALT."
> DEFOVR;DEFALT.
< DEFOVR.
< DEFALT.
```

### Switch Operation Mode

USBHID:

```
$ ./honeywell-config PAP131.
> PAP131.
< PAP131.
```

Keyboard:

```
$ ./honeywell-config PAP124.
> PAP124.
< PAP124.
```

### Add Prefix to Output

The following adds the string `FCKAFD ` (ASCII hex `46 43 4B 41 46 44 20`) in front of every scanned barcode:

```
$ ./honeywell-config PREBK246434B41464420.
> PREBK246434B41464420.
< PREBK246434B41464420.
```

Note how this behaves differently from if you were to configure the scanner in-band via scanning config barcodes.
There you would scan a lot of individual codes from the manual:

1. `PREBK2.`
1. `K4K.`
1. `K6K.`
1. ...
1. `K2K.`
1. `K0K.`
1. `MNUSAV.`

On the USB config interface, all of that goes into a single string instead.

### Query Current Beeper Settings

```
$ ./honeywell-config 'BEP?.'
> BEP?.
< BEPFQ12550,FQ2100,RPT1,ERR1,BEP1,BIP0,LVL0,EXZ,GRX,EXE,DFT,LED1.
```

### List all Settings and Their Possible Values

```
$ ./honeywell-config '*.'
> *.
< BEPFQ1100-5000.
< BEPFQ2100-5000.
...
< AXXMOD0|1|2|3|4|5|6|7|8|9|10.
```

## USB Device Access

Please note that this tool normally needs to run as root.  Alternatively, you can set up a udev rule to grant access to the USB device to non-root users.

An example for this can be found in the file `99-honeywell.rules`.
Put this file into `/etc/udev/rules.d`, and run `sudo udevadm control --reload` to load the new ruleset.

Once you replug the scanner, you should have access to it as a regular user.

## Adapting for Other Scanners

The tool currently has hardcoded USB vendor/product IDs for a Honeywell Hyperion 1300G in Keyboard or USBHID modes.

If you have a different Honeywell scanner, and the tool doesn't find it, you can try making this tool work for it:
1. Obtain the USB vendor and product IDs for your scanner, e.g. through `lsusb`.
1. Replace the VID/PID in the following line of code in `honeywell-config.c`:

    ```c
    libusb_device_handle *devh = libusb_open_device_with_vid_pid(ctx, 0x0c2e, 0x0b07);
    ```
1. Recompile the tool with `make`

## License

MIT License